1997 Chevrolet Blazer Recalls & Complaints

DEALERS WILL INSTALL A FUSED JUMPER HARNESS TO THE ELECTRIC OUTSIDE REARVIEW MIRROR SWITCH. OWNER NOTIFICATION BEGAN ON APRIL 24, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT CHEVROLET AT 1-800-222-1020 OR GMC AT 1-800-462-8782.

CERTAIN SPORT UTILITY VEHICLES, MINI VANS, AND PICKUP TRUCKS MAY DEVELOP A SHORT CIRCUIT IN THE ELECTRIC OUTSIDE REARVIEW MIRROR SWITCH.

SABERSPORT WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON MAY 11, 2009. OWNERS MAY CONTACT SABERSPORT AT 1-909-598-7589.

SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.

ANZO WILL NOTIFY OWNERS AND REPLACE THE HEADLAMPS FREE OF CHARGE. THE RECALL BEGAN MAY 9, 2006. OWNERS MAY CONTACT ANZO USA AT 909-468-3688.

CERTAIN ANZO COMBINATION HEADLAMP ASSEMBLIES SOLD AS REPLACEMENT LAMPS FOR USE ON CERTAIN PASSENGER VEHICLES. SOME COMBINATION LAMPS ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS WHICH FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."

DEALERS WILL REPLACE BOTH UPPER BALL JOINTS. OWNER NOTIFICATION BEGAN SEPTEMBER 4, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT CHEVROLET AT 1-800-222-1020, GMC AT 1-800-462-8782, OR OLDSMOBILE AT 1-800-442-6537.

ON CERTAIN SPORT UTILITY VEHICLES ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN, AND IN THE DISTRICT OF COLUMBIA. FAILURE OF AN UPPER CONTROL ARM BALL JOINT ASSEMBLY COULD OCCUR DUE TO CORROSION.

GM HAS DECIDED TO CONDUCT A CUSTOMER SATISFACTION CAMPAIGN TO REPLACE THE UPPER BALL JOINTS ON AFFECTED VEHICLES. THIS SPECIAL POLICY IS FOR A PERIOD OF 8 YEARS OR 100,000 MILES, WHICHEVER OCCURS FIRST, FROM THE DATE THE VHEICLE WAS ORIGINALLY PLACED IN SERVICE, REGARDLESS OF OWNERSHIP. THE UPPER BALL JOINT REPLACEMENT, DUE TO SEPARATION, WILL BE MADE AT NO CHARGE TO THE CUSTOMER DURING THIS PERIOD. OWNERS CAN CONTACT CHEVROLET AT 1-800-222-1020, GMC AT 1-800-862-4389, OR OLDSMOBILE AT 1-800-442-6537, CONCERNING THIS PROGRAM.

THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH THE SAFETY ACT. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. VEHICLE DESCRIPTION: 1996-1997 4-WHEEL DRIVE CHEVROLET BLAZER, GMC JIMMY, AND OLDSMOBILE BRAVADA SPORT UTILITY VEHICLES. SOME OWNERS HAVE HAD TO PAY FOR REPLACEMENT OF THE UPPER BALL JOINTS THAT HAVE SEPARATED. GM IS PROVIDING A SPECIAL POLICY TO THESE OWNERS TO COVER UPPER BALL JOINT REPLACEMENT IF THE CUSTOMER FOLLOWED THE RECOMMENDED MAINTENANCE SCHEDULE FOR THE CHASSIS LUBRICATION AND THE VEHICLE STILL REQUIRED THE REPLACEMENT OF THE UPPER BALL JOINTS DUE TO SEPARATION.

DEALERS WILL REPLACE THE ENERGY-ABSORBING SEAT BELT ASSEMBLIES WITH ONE THAT DOES NOT HAVE THE ENERGY-ABSORBING LOOP. OWNER NOTIFICATION BEGAN ON AUGUST 8, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT CHEVROLET AT 1-800-222-1020, GMC AT 1-800-462-8782, OR OLDSMOBILE AT 1-800-442-6537.

CERTAIN SPORT UTILITY VEHICLES WERE BUILT WITH A DRIVER'S SEAT BELT BUCKLE ASSEMBLY THAT CONTAINS AN ENERGY-ABSORBING LOOP. SUSTAINED LOADS OF SUFFICIENT MAGNITUDE AND DURATION ON THE BELT IN SEVERE CRASHES COULD FULLY DEPLOY THE BUCKLE ENERGY-ABSORBING LOOP, INTRODUCING A TOTAL OF 10 ADDITIONAL INCHES OF WEBBING INTO THE SEAT BELT SYSTEM. THE FREE FALLING LATCH PLATE USED IN THIS SYSTEM MAY ALLOW WEBBING TO DYNAMICALLY DISTRIBUTE BETWEEN THE LAP AND SHOULDER BELT AS THE DRIVER'S POSITION CHANGES DURING A MULTIPLE ROLLOVER EVENT.

DEALERS WILL INSTALL A PROTECTIVE COVER OVER THE RECLINER MECHANISM.

VEHICLE DESCRIPTION: EXTENDED CAB PICKUP TRUCKS EQUIPPED WITH 60/40 FRONT BENCH SEATS AND EXTENDED CAB PICKUP TRUCKS AND 2-DOOR UTILITY VEHICLES EQUIPPED WITH MANUAL LOCKING RECLINER BUCKET SEATS. THE OUTBOARD SAFETY BELT WEBBING ON THE DRIVER'S AND/OR PASSENGER'S SEAT CAN SEPARATE DURING A FRONTAL IMPACT.