1996 Chrysler Cirrus Recalls & Complaints

AIRTEX WILL NOTIFY OWNERS AND REPLACE THE DEFECTIVE FUEL PUMP MODULES FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 18, 2006. OWNERS MAY CONTACT AIRTEX TOLL-FREE AT 1-866-867-3759.

CERTAIN AIRTEX FUEL PUMP MODULES, P/NOS. E7089M, E7094M, E7113M, AND E7129M, MANUFACTURED BETWEEN JUNE 1 AND SEPTEMBER 24, 2006. THESE FUEL PUMP MODULES WERE SOLD AS AFTERMARKET FOR USE IN CERTAIN DAIMLERCHRYSLER VEHICLES LISTED ABOVE. SILICONE MATERIAL USED IN MANUFACTURE OF THE FLAPPER VALVE WAS OUT-OF-SPECIFICATION, LEADING TO EXCESS SWELL OF THE FLAPPER VALVE RESTRICTING THE FLOW OF FUEL TO THE FUEL PUMP MODULE.

TI AUTOMOTIVE WILL NOTIFY OWNERS AND REPLACE THE DEFECTIVE FUEL PUMP MODULES FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 6, 2006. OWNERS MAY CONTACT TI AUTOMOTIVE TOLL-FREE AT 1-877-461-1834.

CERTAIN TIGAS FUEL PUMP MODULES MANUFACTURED BETWEEN JUNE 1 AND SEPTEMBER 24, 2006, SOLD UNDER VARIOUS BRAND NAMES AND P/NOS. THESE FUEL PUMP MODULES ARE SOLD AS AFTERMARKET FOR USE IN CERTAIN DAIMLERCHRYSLER VEHICLES LISTED ABOVE. SILICONE MATERIAL USED IN MANUFACTURE OF THE FLAPPER VALVE WAS OUT-OF-SPECIFICATION, LEADING TO EXCESS SWELL OF THE FLAPPER VALVE RESTRICTING THE FLOW OF FUEL TO THE FUEL PUMP MODULE.

DEALERS WILL INSTALL AN EXPANSION PLUG AND RETAINING BRACKET OVER THE CYLINDER HEAD OIL GALLEY PLUG.

IN CERTAIN VEHICLES, THE ENGINE CYLINDER HEAD OIL GALLEY PLUG DOES NOT SEAL PROPERLY AND ENGINE CYLINDER HEAD OIL IS NOT ADEQUATELY RETAINED.

QUALIS AUTOMOTIVE WILL REPLACE THE BALL JOINTS FREE OF CHARGE. THE SAFETY RECALL BEGAN ON NOVEMBER 9, 2009. OWNERS MAY CONTACT QUALIS AUTOMOTIVE AT 1-800-493-4128.

QUALIS AUTOMOTIVE IS RECALLING CERTAIN AFTERMARKET BALL JOINTS SOLD FOR USE ON CERTAIN PASSENGER VEHICLES. THE SOCKET MAY HAVE BEEN EXCESSIVELY HARDENED WHICH COULD CAUSE IT TO CRACK NEAR THE RETAINING RING GROOVE ALLOWING THE BALL STUD TO SEPARATE UNDER IMPACT LOAD. THE SUBJECT BALL JOINTS WERE SOLD AS FOUR PART NUMBERS, D10945, D10946, G10945, AND G10946. THE AFFECTED CONTROL ARMS, D10945 AND D10946, ARE STAMPED WITH THE FOLLOWING DATES ON THE BALL JOINTS: 134308, 135708, 100109, 102709, 104109, 105509, 107609, 108909, 110309, 113209, AND 116609. THE G10945 AND G10946 ARE THE SAME PART AS THE D10945 AND D10946 RESPECTIVELY. THEY ARE LABELED DIFFERENTLY DEPENDING ON THE AFTERMARKET CUSTOMER.

FEDERAL-MOGUL WILL NOTIFY OWNERS OF RECORD AND REPLACE THE AFFECTED CONTROL ARMS FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JANUARY 28, 2011. OWNERS MAY CONTACT FEDERAL-MOGUL AT 1-877-489-6659.

FEDERAL-MOGUL IS RECALLING CERTAIN REPLACEMENT CONTROL ARM ASSEMBLIES, PART NUMBERS K7425, 10945, FA4510X, K7427, 10946, AND FA4611X, SOLD FOR USE ON VARIOUS PASSENGER VEHICLES LISTED ABOVE. THE BALL JOINT ON THE CONTROL ARM ASSEMBLY CAN FAIL CAUSING THE BALL STUD TO WEAR THROUGH THE CONTROL ARM HOUSING RESULTING IN NOISE AND/OR SEPARATION OF THE BALL STUD FROM THE HOUSING.

DEALERS WILL REPLACE THE SECONDARY HOOD LATCH SPRING WITH A LONGER END HOOK SPRING.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE SECONDARY HOOD LATCH SPRING CAN DISENGAGE FROM ITS RETENTION HOLE IF THE HOOD IS SLAMMED SHUT.

DEALERS WILL INSPECT THE BALL JOINT END HOUSING COVER SEAL FOR LEAKAGE WITH A HIGH PRESSURE AIR TESTER AND THE RUBBER BOOT WILL BE VISUALLY INSPECTED FOR DAMAGE. IF THE COVER SEAL LEAKS OR THE BOOT IS DAMAGED, THE LOWER CONTROL ARM WILL BE REPLACED.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE LOWER CONTROL ARM BALL JOINT CAN SEPARATE DUE TO LOSS OF LUBRICATION.

DEALERS WILL INSTALL A NEW LOAD-LIMITING PUSH ROD INTO THE FLOOR SHIFTER LEVER OF THE AFFECTED VEHICLES. OWNER NOTIFICATION BEGAN ON JUNE 14, 2004. OWNERS SHOULD CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.

ON CERTAIN PASSENGER VEHICLES, THE FLOOR SHIFTER IGNITION-PARK INTERLOCK MAY FAIL AND ALLOW THE SHIFTER TO BE MOVED OUT OF THE PARK POSITION WITH THE KEY REMOVED. AN INOPERATIVE INTERLOCK MAY ALSO ALLOW THE KEY TO BE REMOVED WHEN THE SHIFTER HAS NOT BEEN PLACED IN THE PARK POSITION.

DEALERS WILL REPLACE THE REAR BRAKE MASTER CYLINDR PISTON ASSEMBLY.

THE BRAKE MASTER CYLINDER CAN LEAK BRAKE FLUID DUE TO A DAMAGED DOUBLE LIP REAR PISTON SEAL.

DEALERS WILL INSPECT FOR PROPER OPERATION OF THE SYSTEM. ANY VEHICLES THAT ARE NOT FUNCTIONAL AFTER THE INSPECTION WILL HAVE THE SHIFT MECHANISM AND CABLE REPLACED WITH A "SELF-ADJUSTING" DESIGN.

VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH AUTOMATIC TRANSMISSIONS. THE ADJUSTMENT OF THE CABLE CONNECTING THE CONSOLE SHIFTER MECHANISM TO THE IGNITION KEY CAN CAUSE A TRAPPED KEY CONDITION WHICH CAN RESULT IN A LOW FORCE REQUIRED TO DEPRESS THE SHIFT BUTTON. A COMBINATION OF APPLYING A MIS-ADJUSTED RELEASE BUTTON WITH A LOW FORCE ATTEMPT TO SHIFT OUT OF PARK WITH THE KEY IN THE LOCKED POSITION, CAN BREAK THE CONNECTING PIN IN THE SHIFTER.

DEALERS WILL INSTALL A PLATE AND SILICONE GREASE INJECTED INTO THE SOLENOID CAVITY TO ELIMINATE THE POTENTIAL FOR THIS CONDITION.

CORROSION OF THE ABS HYDRAULIC CONTROL UNIT CAN CAUSE THE SOLENOID VALVES TO STICK IN THE OPEN POSITION.