2007 Hino Nv8j Recalls & Complaints

Hino will notify owners, and dealers will repair the vehicles free of charge. The recall began on January 17, 2013. Owners may contact Hino at 1-248-699-9390.

Hino is recalling certain model year 2005 through 2013 medium duty trucks, models NA6J, NB6J, NC6J, ND8J, NE8J, NJ8J, NF8J, and NV8J, manufactured from August 18, 2003, through November 16, 2011. Over time, the main B+ circuit from the battery to the starter could potentially short to ground due to wear that accumulates as a result of interference between the B+ circuit and its convoluted tubing sheath.

DEALERS WILL REPLACE THE AUTO TENSIONER, INSTALL UPGRADED MOUNTING BOLTS, AND REPLACE THE ACCESSORY DRIVE BELT FREE OF CHARGE. THE RECALL BEGAN ON APRIL 25, 2007. OWNERS MAY CONTACT HINO MOTORS AT 248-648-6430. NOTE: THIS RECALL SUPERSEDES A PREVIOUS CAMPAIGN (PLEASE SEE 06V157).

ON CERTAIN TRUCKS EQUIPPED WITH BANDO BELT TENSIONER, CORROSION OR RUST MAY DEVELOP ON THE TENSIONER SPINDLE OR BUSHING CAUSING THE AUTO TENSIONER TO BECOME STIFF OR BIND. THIS CAN CAUSE THE DRIVE BELT TO SUDDENLY COME OFF OR THE AUTO TENSIONER MOUNTING BOLTS COULD SUDDENLY BREAK.

DEALERS WILL INSPECT THE STEERING ARM TIGHTNESS AND REMOVE ALL GREASE AND PAINT FROM THE STEERING ARMS AND RETORQUE THE DRAGLINK ATTACHMENT NUTS AT THE STEERING ARM AND PITMAN ARM. THE RECALL BEGAN ON MAY 12, 2006. OWNERS MAY CONTACT HINO AT 1-248-648-6430.

ON CERTAIN TRUCKS, DURING ASSEMBLY, THE DRAG LINK ATTACHMENT NUTS AT THE PITMAN ARM AND STEERING ARM MAY HAVE BEEN INCORRECTLY TORQUED. RESIDUAL GREASE AND PAINT WHICH WAS APPLIED AS A RUST INHIBITOR ON THE STEERING ARM MAY HAVE CONTRIBUTED TO A LOSS OF TORQUE AFTER ASSEMBLY.

DEALERS WILL REPLACE THE VERTICAL FRONT SPRING BRACKET ATTACHMENT BOLTS ON RIGHT/LEFT HANGER BRACKETS AND RE-TORQUE ALL ASSOCIATED BOLTS FREE OF CHARGE. THE RECALL BEGAN ON SEPTEMBER 8, 2008. OWNERS MAY CONTACT HINO AT 248-699-9300.

HINO IS RECALLING 16,805 MY 2005-2008 NA6J, NB6J, NC6J, ND8J, NE8J, NJ8J, AND NV8J TRUCKS. THE TWO VERTICAL RIGHT/LEFT SIDE FRONT SPRING BRACKET BOLTS WERE NOT TIGHTENED PROPERLY DURING THE ASSEMBLY PROCESS. THIS MAY CAUSE INCREASED STRESS ON THE SPRING BRACKET WHICH CAN LEAD TO CRACKING OF THE BRACKET.

DEALERS WILL REPLACE THE PROPELLER SHAFT BOLTS. THE RECALL BEGAN ON OCTOBER 14, 2008. OWNERS MAY CONTACT HINO AT 1-248-699-9300.

HINO IS RECALLING 1,195 MY 2007-2009 NV8J TRUCKS. DURING THE MANUFACTURING PROCESS, THE PROPELLER SHAFT BOLTS MAY NOT HAVE BEEN PROPERLY TIGHTENED DURING THE MANUFACTURING PROCESS.

DEALERS WILL INSPECT THE AIR BRAKE LINES, DRIVE SHAFT BOLTS AND ABS SENSOR CLIPS AND TIGHTEN AND REPAIR IF NECESSARY. THE RECALL BEGAN ON SEPTEMBER 15, 2006. OWNERS MAY CONTACT HINO AT 1-248-648-6430.

ON CERTAIN CAB AND CHASSIS TRUCKS THAT WERE TRANSPORTED TO THE SELLING LOCATION OR BODY COMPANY USING A DECKING SYSTEM (VEHICLES STACKED ON THE REAR OF THE LEAD TRUCK FOR TRANSPORT), THE AIR BRAKE LINES MAY BE DISCONNECTED SO THAT THE BRAKING SYSTEMS CAN BE TIED TOGETHER WITH THE OTHER VEHICLES. WHEN THESE VEHICLES ARRIVE AT THEIR DESTINATION, THE AIR BRAKE LINES ARE RECONNECTED. THESE RECONNECTIONS WERE NOT ALWAYS BEING TIGHTENED TO THE PROPER TORQUE. ALSO, DURING THIS RECONNECTION PROCESS, SOME OF THE ABS WIRING CLIPS HAD BEEN REMOVED AND NOT REINSTALLED.

DEALERS WILL INSPECT, CORRECT, AND REPLACE THE CROSSMEMBERS. THE RECALL BEGAN ON DECEMBER 4, 2006. OWNERS MAY CONTACT HINO AT 1-248-648-6400.

ON CERTAIN VEHICLES, DURING THE STAMPING PROCESS, SOME CROSSMEMBERS WERE MANUFACTURED WITH A DEFORMATION TO THE LOWER CORNERS DUE TO EXCESSIVE WEAR OF THE STAMPING DIE. OVER TIME, IF THIS CONDITION WERE IGNORED, THE STRUCTURAL INTEGRITY OF THE CROSSMEMBERS COULD BE COMPROMISED WHICH COULD RESULT IN A LOSS OF BRAKING ABILITY, SEPARATION OF THE PROPELLER SHAFT AND/OR A LOSS OF REAR WARNING LAMPS.