2003 Nissan Sentra Recalls & Complaints

Nissan will notify owners, and dealers will replace the front passenger air bag inflators with alternate desiccated inflators, free of charge. The recall began February 12, 2020. Owners may contact Nissan customer service at 888-737-9511 or Infiniti customer service at 888-810-3715.

Nissan North America, Inc. (Nissan) is recalling certain 2001-2003 Maxima, 2002-2006 Sentra, 2002-2004 Pathfinder, 2007-2011 Versa Sedan and Versa Hatchback, 2001-2004 Infiniti I30 and I35, 2002-2003 Inifiniti QX4, 2003-2008 Infiniti FX35 and FX45 and 2006-2010 M35 and M45 vehicles. The vehicles are equipped with non-desiccated, frontal passenger air bag inflators containing phase stabilized ammonium nitrate (PSAN) propellant that were used as interim remedy parts for previous Takata recalls. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.

Owners are advised not to drive their vehicles until the repair has been completed. Nissan will notify owners, and dealers will re-inspect the vehicle and, if necessary, replace the air bag inflator, free of charge. The recall began January 22, 2021. Owners may contact Nissan customer service at 1-800-867-7669. Nissan's number for this recall is PM964.

Nissan North America, Inc. (Nissan) is recalling certain 2002-2006 Sentra vehicles whose passenger air bags were previously inspected and may have been released without replacing the Takata air bag inflator. In the event of a crash, Takata frontal passenger air bag inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.

Dealers will inspect and replace the inflators as necessary, free of charge. Owner notification letters are expected to be mailed September 14, 2022. Owners may contact Nissan's customer service at 1-800-867-7669.

Nissan North America, Inc. (Nissan) is recalling certain air bag inflator replacement service parts that may have been installed as part of a theft or collision repair. The parts include certain passenger-side air bag inflators designed to fit Infiniti 2002-2003 QX4, 2006-2010 M35 and M45; Nissan 2001-2003 Maxima, 2002-2006 Sentra, and both driver and passenger-side inflators designed to fit 2007-2012 Versa Sedan and Versa Hatchback vehicles. Please see Nissan's recall report for the specific part numbers. These replacement inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

Nissan will notify owners, and dealers will replace the passenger air bag inflator, free of charge. The recall began on June 15, 2015. Owners may contact Nissan customer service at 1-800-647-7261. Note: On December 18, 2015 Nissan informed NHTSA of an amendment of this recall to remove 2004-2005 Infiniti FX35 and FX45 vehicles.

Nissan North America, Inc. (Nissan) is recalling certain model year 2001-2003 Nissan Maxima, 2002-2004 Pathfinder, 2002-2006 Sentra, 2002-2003 Infiniti QX4 and I35, 2003 FX35 and FX45, and 2001 I30 vehicles. Upon deployment of the passenger side frontal air bag, excessive internal pressure may cause the inflator to rupture.

DEALERS WILL REPROGRAM THE ECM FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 21, 2006. OWNERS MAY CONTACT NISSAN AT 1-800-647-7261.

ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH A 2.5L ENGINE, THE CRANK ANGLE SENSOR IS AFFECTED BY TEMPERATURE VARIATIONS. UNDER CERTAIN DRIVING CONDITIONS, THESE VARIATIONS IN TEMPERATURE CAN BE LARGE ENOUGH TO CAUSE A BRIEF INTERRUPTION IN THE SIGNAL OUTPUT FROM THE SENSOR.

DOPE, INC. WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON JULY 28, 2009. OWNERS MAY CONTACT DOPE, INC. AT 1-626-272-1798.

DOPE, INC. IS RECALLING 42,540 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.

TRADESONIC WILL NOTIFY OWNERS AND REPLACE THE LAMPS FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN DURING JULY 2006. OWNERS MAY CONTACT TRADESONIC AT 626-934-8884.

CERTAIN TRADESONIC COMBINATION LAMPS SOLD AS REPLACEMENT LAMPS FOR USE ON THE ABOVE LISTED PASSENGER VEHICLES. COMBINATION LAMPS NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.

DEALERS WILL REMOVE THE INSIDE LINING MATERIAL FROM THE ECM BOX. OWNER NOTIFICATION BEGAN ON DECEMBER 22, 2003. OWNERS SHOULD CONTACT NISSAN AT 1-800-647-7261.

ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH THE QG18DE ENGINE OR QR25DE ENGINES, THE FOAM MATERIAL USED FOR THE INTERIOR LINING OF THE ELECTRONIC CONTROL MODULE (ECM) BOX EMITS SULFUR AS IT CURES.

DEALERS WILL REPLACE THE CRANK POSITION SENSORS. CAMSHAFT POSITION SENSOR(S), AND IN SOME CASES, THE VARIABLE TIMING CONTROL SENSOR(S). VEHICLES INVOLVED IN A PREVIOUS RECALL CAMPAIGN, 01V357, ARE ALSO INCLUDED IN THIS NEW CAMPAIGN. THE REPLACEMENT SENSORS USED IN THAT CAMPAIGN ARE ALSO AFFECTED. OWNER NOTIFICATION BEGAN ON DECEMBER 22, 2003. OWNERS SHOULD CONTACT NISSAN AT 1-800-647-7261 OR INFINITI AT 1-800-662-6200.

ON CERTAIN PASSENGER VEHICLES, THE CIRCUIT BOARD FOR THE CRANK POSITION SENSOR OR CAM POSITION SENSOR MAY HAVE AN IMPROPER SOLDER JOINT DUE TO SOLDER DEFORMATION CAUSED BY HEAT STRESS ACCELERATED BY THE EXISTENCE OF FLUX RESIDUE DURING THE SOLDERING PROCESS.

DEALERS WILL REPLACE THE BRACKET ON THESE VEHICLES. OWNER NOTIFICATION BEGAN DECEMBER 15, 2003. OWNERS SHOULD CONTACT NISSAN AT 1-800-647-7261.

ON CERTAIN ELECTRIC VEHICLES, THE FRONT SUSPENSION TRANSVERSE LINK'S BALL JOINT BRACKET MAY BREAK FROM STRESS CONCENTRATION AT A NOTCH CREATED BY SURFACE ROUGHNESS AND THE SHAPE OF THE MATERIAL CUT-LINE.